Balanced Knee® System

Engineering simplicity in the Balanced Knee® System (BKS) permits easy restoration of balance in both flexion/extension and varus/valgus. Comprehensive instrumentation is designed for ease-of-use and repeatability in the hands of every surgeon. A wide selection of implants allows for balancing refinement to the nearest millimeter for superior results in difficult surgical cases.

The following features and benefits make the Balanced Knee® System (BKS) a good choice in your practice:

• The femoral components are available in five options to allow for surgeon preference
  
• The one-piece tibial tray design is available in three options
  
• Patented tibial insert locking mechanism shows 94% less micromotion than the industry standard
  
• Tibial inserts are available in 1mm increments in the most popular thicknesses to give the surgeon the ability to micro tune the knee during trial reduction
  
• The dome shaped patella insures maximum conformity with the deepened trochlear groove in the femoral component, even in deep flexion
  

Balanced Knee® System Revision

The Sonoma Anterior Cervical Plate System offers both rigid and semi-rigid constructs, utilizing a low profile plate and self-locking screws. The plate is pre-lordosed for better anatomic fit and has large windows for viewing the disc space and graft site. The self-locking screws require no additional locking mechanisms or steps and lock flush to the plate. The Sonoma System offers a variety of plate lengths and multiple screw options including primary and rescue sizes as well as variable and limited angle screws.

Encompass® Hip Stem Cemented

The Encompass® Hip Stem Cemented features an optimized neck design and is available in standard and extended offset options. The instrumentation for the Encompass® System was designed to allow for simple intraoperative transition from a press-fit option to a cemented stem design if required based on a patient's bone quality.

• Optimized neck geometry with a shorter trunion section to provide greater range of motion
• Highly polished neck section to help decrease debris wear potential
  
• A/P normalization steps to help with stabilization in cement mantle
• Two neck offset options - standard and extended

Encompass® Hip Stem Plasma Spray

Today's orthopedic implants offer surgeons many options with varying philosophies for total hip replacement (THR). The Encompass® Hip Stem Plasma Spray offers precise distal fit as well as maximum proximal fill. This is a unitized stem with an optimized neck geometry and is available in standard and extended offset options.

• Optimized neck geometry for increased range of motion
  
• Highly polished neck finish to help decrease wear debris potential
  
• Plasma spray coating to provide initial and long-term fixation
  
• Two neck offset options - standard and extended
  
• Distal flutes for anti-rotation and distal stabilization

Ovation™ Hip Stem

Ortho Development introduces the Ovation™ Hip Stem, an innovation in design and simplicity that reduces bone loss and length of surgery. To provide options for various patients needs, the Ovation is available in a range of sizes with both standard and extended neck offset options.

• Tapered stemdesign provides excellent rotational stability and promotes 3-point fixation
  
• Minimal instrumentation simplifies surgical procedure.
  
• Streamlined profile is bone conserving
  
• Optimized neck geometry with highly polished surface improves overall range of motion and decreases wear
  
• Available in 12 sizes with standard and extended neck offsets to accommodate patient anatomy
  
• Proximal body surface is coated with titanium plasma spray for solid, long-term fixation
  
• Distal body flute to more closely match bone properties
  

Pivot Bipolar®

The Pivot Bipolar® was designed with a simple one-step assembly interface between the femoral head and the compression molded liner that requires no instruments and reduces OR time.

• Simple one-step assembly requires no instruments
  
• Compression Molded UHMWPE
  
• 75° Range of Motion (12/14 taper on 28mm head)
  
• Available in 38-60mm (1mm increments)

Tri-plus® Acetabular System

The Tri-plus® Acetabular shell is a true hemispherical design featuring plasma spray coating which allows the substrate to retain its fatigue strength characteristics. The shell and liner utilize a secure locking mechanism designed to decrease the potential for polyethylene wear debris. The liner is manufactured from direct-compression molded polyethylene and incorporates anti-rotation features.

• The locking mechanism allows for secure fixation between the shell and liner
  
• Superior surface tabs designed into liner provides anti-rotation stability and proper liner indexing
  
• The shell is a true hemisphere design available in No-hole, Cluster hole, and Multihole options
  
• The liners are available in Neutral and Hooded (10°) options
  
• The Tri-plus™ liners are manufactured from DCM polyethylene

Solitude® Unipolar

The Solitude® Unipolar features a simple intraoperative assembly. It is available in sizes 38-60mm (1mm increments). Also the trunion adapters are available in -3, +0, +3, +6, and +9mm options.

Legend® All-poly Cup

The Legend® All-poly Cup was designed to provide surgeons with a one-piece cemented acetabular option for total hip arthroplasty. The cup is manufactured from compression molded UHMWPE and is available in both neutral and hooded (10°) options to accommodate patient's needs.

• Integral cement spacers to provide uniform 2mm cement mantle
• X-ray Markers - equatorial and polar wires for reference
  
• Groves and ridges to help prevent rotation at insertion
  
• Compression molded UHMWPE
  
• Available in sizes 40-62mm (2mm increments)
  
• 22mm and 28mm inner diameter
  
• Neutral and hooded (10°) options

Hemisphere® Modular Cup

The Hemisphere® Modular Cup is designed to decrease polyethylene debris and increase the overall stability of the implant. The instrumentation is designed to provide the surgeon with accuracy and reproducible results each time the cup is implanted.

• A full range of sizes in both no-hole and cluster hole options designed with a flared rim to increase fixation
  
• Available in neutral and 15 degree hooded liners both designed to accommodate 22, 26, and 28mm femoral heads
  
• Locking tabs on the face of the shell reduce relative motion of the liner
  
• One liner size for every size shell in all but the largest shell sizes to avoid compromising the liner thickness

Primaloc® Cementless Hip

The Primaloc® Hip System was designed for ease-of-use by reducing intraoperative steps and excess inventory. The system is designed as a one-piece stem with the ability to accommodate the needs of a completely modular system. The instrumentation provides precise control and reproducible technique each and every time. The following features and benefits will help you understand why the Primaloc® Cemenentless Hip would be a great choice for your patients.

• A one-piece stem design available in both collared and collarless options to allow for surgeon preference
  
• A full range of proximal femoral configurations without adding excess modularit.
  
• Enhanced proximal geometry provides initial fixation and maximizes anterior/posterior conformity
  
• The distal geometry offers a bullet-tip with a coronal slot to reduce stiffness
  
• The distal flutes allow for enhanced rotational stability

Envision®2 Anterior Cervical Plate

The Envision®2 Anterior Cervical Plate has a unique blend of features designed for easier and more reliable cervical fusion. Engineered with functionality and simplicity in mind, the Envision plate combines load sharing properties with strength and ease-of-use. The 2.0mm low profile plate virtually eliminates soft tissue irritation and the one-step locking mechanism is simple to engage.

• Thin and narrow design minimizes tissue irritation and accommodates patient anatomy
  
• Pre-contoured shape simplifies surgery by minimizing need for plate bending without sacrificing strength and flexibility
  
• Large graft windows facilitate graft visualization
  
• Patented one-step locking mechanism helps prevent screw back-out without extra steps or components; simplifies installation and revision

Vusion® TS/PS/CS

The Vusion® Partial Vertebral Body Replacement is manufactured from PEEK-OPTIMA® polymer with radiopaque markers and is available in parallel and lordotic options.

• Manufactured from radiolucent PEEK-OPTIMA polymer
  
• Large fenestrations for bone grafting
  
• Contoured, anatomical shapes
• Radiopaque markers for intra-operative orientation and post-operative visualization
  
• Tapered nose facilitates insertion
  

Cervical Allograft

The Milled Cortical Wedge features a machined-through hole, machined ridges, a simple inserter interface, and is available in sizes 5mm to 10mm in height. The tissue as been retrieved under aseptic technique and is then processed aseptically and lyophilized for storage. The Cervical Allograft Milled Cortical Wedge is a product of Bacterin International, Inc. and is distributed by Ortho Development.

IBS® Allograft Lumbar

The primary goals in interbody fusion are to immobilize the affected vertebrae, to restore disc space height and sagittal alignment, and to provide an environment for bone fusion between vertebral bodies. The IBS® Allograft is designed to promote these goals as well as surgeon skills and training.

• Solid, one-piece femoral cortical allograft (not composite) gives strength and integrity
  
• Superior and inferior surface grooves enhance the surface for increased area and migration resistance
  
• Crescent shape facilitates placement and orientation
  
• Tapered leading edge facilitates insertion into limited space
  
• IBS® Allograft is compatible with any posterior pedicle screw fixation system